Boost Bottle Installation for Motorized Bikes Tutorial | 66cc 80cc 49cc 50cc 2-Stroke
bicycles reviews | bicycles videos | bicycles online
A quick and easy tutorial on how to install your boost bottle that will take your gas bike to the next level! Get your boost bottle here ► http://bit.ly/1OWNE2F BikeBerry.com ►http://bit.ly/1FZ8nPp Facebook ► http://on.fb.me/1wWG4fD Instagram ► http://bit.ly/1aM3WxZ Twitter ► https://twitter.com/bikeberrycom Everything you need to make your own Motorized Bicycle.
Comments
-
I get the engine to start by releasing n then holding the clutch but then when I release the clutch handle again the engine turns off. The bike doesn't move people tell me the chain is too tight or change the pads in the clutch did that too everything seems to be working except the chain doesn't engage with motor please help
-
how do you guys install a basic jackshaft kit? it's hard to find a good tutorial on here. I don't have the SBR one.
-
how should I know what size manifold to get 40 or 30mm
-
My bike when it get almost to top end it just starts bogging out so i have to go really slow on the throttle or it dies on me but eventually over time it does gain speed do you think a boost bottle would solve this issue?? ive replaced the carberator three times now thinking that was the problem but have had no success.
-
Hey Allen I see a Nitrogen oxide kit for sale on the web for the motor bikes. Now with a aluminum cylinder and head this would VERY dangerous right? And with that being said has anyone been looking into a steel sleeve for the 2 strokes cylinders? I would buy 2 or 3 right now. ( <and that's not a joke)
-
Could I use this on a 212 pred or would I be wasting my time ordering it
-
i really dont know how it work do you need to put gaz in the boost bottle and how long the boost bottle last
-
Chain getting stuck in engine
-
I feel that I want to go with a 4 stroke and just run reg gas...
Do you have mods and upgrades for 4 stroke or am I stuck with 15-20 mph. -
I have a schwinn oc chopper and was wondering if you could make an installation video with a 66cc motor kit.
-
my bar is to thick for motor mount.help me
-
Where do you buy thath i want one
-
Would it be ok if i were to put the hole side of the intake on the bottom? I'm not getting enough space for the tube not to melt on the cylinder head.
-
okay so i cant be the only one having an issue with the bolts and a tool not fitting in to where the modified intake is supposed to hold. the holes are just big enough to clear the bolt but i cant get around it to tighten it down... any help or suggestions?
-
BEWARE ordering from Bike Berry. They are con artists and frauds with several scam websites. They take your money for weeks without telling you there's an issue in shipping or billing. The customer service is even worse. Total douche bags. Order from someone else... preferably a local builder and not this money grubbing jackass company.
-
couch not working
-
couch not working
-
Why did my front motor mount bolts break? Answer, cheap soft metal bolts. ACE is the place to buy better stud bolts. This is how I modified the standard throttle cable to accommodate the high performance carb. I cut back some of the nylon throttle stop material at the opposite end of the throttle cable allowing the cable to go further into the carburetor to hook up to that sliding throttle plate.
-
ISSUE (since you requested them): My sprocket, rubber rings and metal clamps do NOT come with lined up holes. I had to use a drill press to fix this... Just thought I'd let you know.
-
What's better?
Expansive pipe + H.P. Carb+ reed vavles
Or
Expansive pipe + HP Carb + boost bootle?
Any input would gr8t
2m 14sLenght
244Rating